Geogrids & Geocells
HERMEQ supplies geogrid for stabilising weak soils and reinforcing the granular layers of roads, car parks, haul roads and working platforms in construction and civil engineering. The range covers polypropylene biaxial geogrids, including Lotrak, alongside the Tensar TriAx and InterAx systems.
Laid beneath aggregate, a geogrid confines the stone, spreads load over a wider area of subgrade and limits movement within the sub-base. This improves bearing capacity, controls rutting and settlement, and gives a stable foundation on soft and variable ground. Geogrid mesh is held in permanent UK stock and can be bought online for next day delivery nationwide.
Geogrid mesh with square and multi-axial apertures
The three types differ in the shape of their apertures, and with it in how each grid locks into the aggregate and spreads load through the layer above.
Biaxial geogrid
A biaxial geogrid has square apertures and the same tensile strength along the roll as across it. It is the established choice for general reinforcement of a sub-base or capping layer, and for any job where the specification gives a strength grade in kN per metre in both directions. HERMEQ supplies its own polypropylene biaxial geogrid in three grades, and Lotrak biaxial geogrid for projects that call for that brand.
Tensar TriAx geogrid
Tensar TriAx geogrid is a multi-axial grid, with ribs running in three directions to form triangular apertures. It is used to stabilise trafficked granular layers such as haul roads, access roads and working platforms, and is the grid to choose where the design has been carried out around TriAx or the specification names it. Each grade is matched to a level of traffic and ground, so the grade on the drawing is the one to order.
Tensar InterAx geogrid
Tensar InterAx geogrid is a Tensar system for stabilising the granular layers of roads, railways and other trafficked areas, and it is ordered when a project has been designed around InterAx.

Biaxial geogrid or Tensar geogrid
The choice follows the design. A biaxial grid suits general reinforcement of a sub-base or capping layer where the specification states a tensile strength in kN per metre in two directions, which is how many haul roads, yards and car park sub-bases are specified when no proprietary system is named. Where the specification gives a grade and allows an equivalent, the HERMEQ biaxial grid and Lotrak are both options at that grade.
Tensar TriAx and InterAx suit projects designed around those systems, where the designer has used the manufacturer's design method to set the aggregate depth for a given traffic load and subgrade. If a Tensar product is named on the drawings or in the specification, do not substitute a biaxial grid, or a different Tensar grade, without the designer's written approval.
Geogrid reinforcement for roads, car parks and working platforms
What decides the grid for each use is the traffic it carries, the strength of the subgrade, the depth of fill above it and how long the surface has to last.
Haul roads and site access roads
Site haul roads carry repeated passes of loaded dumpers, wagons and plant over ground that often softens in wet weather, so the grid is chosen for the heaviest axle load and the worst ground along the route. A geogrid beneath the stone limits rutting of the running surface and cuts the volume of aggregate brought in, and taken away again, when the road comes out. Where access is needed for only days or weeks, or the route moves as the work progresses, ground protection mats laid on the surface do the job without excavation or imported stone.
Roads, car parks and hardstanding
Under permanent roads, car parks and storage yards, the grid sits in the sub-base beneath the finished surface and carries traffic for the life of the pavement, so the grade follows the design traffic and the subgrade strength at formation level. A geogrid reinforces the layer below the surface and does not hold a loose finish: a gravel car park or driveway needs gravel grids at the surface to keep the stone in place.
Piling and crane platforms
Piling rigs and cranes put high, concentrated loads through tracks and outriggers onto a granular working platform. These platforms are normally designed by a temporary works engineer and covered by a platform certificate, which fixes the grid type, the number of layers and the depth of fill, so the grid ordered must match the one in that design.

Geogrid strength grades and roll sizes
Strength grade
On a biaxial geogrid, 20/20, 30/30 and 40/40 give the ultimate tensile strength in kN per metre along the roll and across it, and the two figures match because the grid is equally strong in both directions. The biaxial range runs from 20 kN to 40 kN. As a general guide, 20/20 goes under lighter traffic on firmer ground, 30/30 is the common grade for sub-bases carrying regular HGV and plant traffic, and 40/40 goes under the heaviest loads on the weakest subgrades. Step up a grade as traffic gets heavier or the ground gets softer, and where both apply, take the higher grade.
Roll width and coverage
Rolls across the range are around 4 m wide and mostly 50 m long. Calculate the area to be covered, add the width lost to overlaps at every side and end joint, allow for trimming at curves and edges, and divide by the area of one roll. Overlap widths depend on the subgrade and are given in the design or the manufacturer's installation guidance.
Geotextile separation
On clay, silt or wet ground, fine soil can be pumped up into the stone under traffic, and a geotextile membrane laid on the formation before the geogrid keeps the two apart. Where water also has to be carried away from the formation, geocomposite drainage goes beneath the build-up.
Popular Categories

Geotextiles
View Products >

Grass & Gravel Paviours
View Products >

Geomembranes
View Products >
Frequently Asked Questions
How does a geogrid work?
When aggregate is compacted over a geogrid, the stone partly passes through the apertures and locks against the ribs. This interlock gives lateral restraint: the particles cannot spread sideways under a wheel or track, so the granular layer stays tight and stiff. A stiffer layer passes load down to the subgrade over a wider area, which lowers the pressure on the soft ground beneath.
Does geogrid reduce the depth of sub-base?
On a designed road, yard or platform, a geogrid usually allows a thinner layer of aggregate for the same traffic and subgrade than unreinforced stone would need. That reduces excavation, imported fill and the material taken off site. The saving is worked out in the design for a specific grid, traffic load and ground condition, so the depth on the drawing is the one to build to.
What is the difference between uniaxial and biaxial geogrid?
A uniaxial geogrid carries its strength along the length of the roll, with only enough strength across it to hold the apertures open, and is used to reinforce retaining walls and steep slopes where the load acts in one direction. A biaxial geogrid has equal strength along and across the roll and is laid flat within a granular layer, where traffic loads act in every direction.
How is geogrid laid and joined?
The formation is cleared of sharp debris, levelled and compacted, with any geotextile separator laid first. Rolls are unrolled flat in the direction of travel and pulled taut, and neighbouring rolls are overlapped at the sides and ends by the width the design or installation guidance gives for the ground. Fill is tipped onto the grid and pushed forward in layers, with plant running on the fill and never directly on the exposed grid.
Can geogrid be cut to size?
Geogrid cuts easily on site with a sharp knife or heavy shears, so rolls can be trimmed to fit edges, curves and obstructions such as manholes. HERMEQ supplies geogrid by the full roll, so it pays to plan the layout around whole roll widths.










































































































































