Accessories
HERMEQ scaffolding accessories are the components that make a scaffold safe to reach, work on and pass beneath, and they can be bought online with next day delivery on many lines. The temporary aluminium stairway is light, quick to erect and gives the workforce stair access to platforms at height. Battery LED scaffold lights mark tubes and edges in poor light. The ReadyFix transom holds scaffold boards in place with fewer fittings, which saves material and labour on tube and fitting scaffold. The 6 tonne base jack is a threaded levelling jack for system scaffold, and the trestle range turns builders trestles into guarded platforms for low-level work at height.
Steel ladder beams or aluminium beams
A bridging beam carries the scaffold across an opening where the standards cannot come down to the ground, such as a doorway, a shop front, a lift shaft, a void in a floor or a roof span, and it also bridges between two scaffolds or towers. The choice between steel and aluminium turns on span, handling, exposure and how the beam is fixed into the scaffold.
Steel ladder beams are welded from circular hollow section in lengths up to 21ft. They are coupled directly into the tube structure and suit heavier bridging over longer openings, where the weight of the beam on the scaffold is not the deciding factor.
The galvanised ladder beams have a zinc finish against corrosion. They are the steel beam to choose where the scaffold will stand for months, or where the site is wet and exposed.
Aluminium scaffold beams, in lengths up to 8.1m, are chosen when manual handling or the weight on the structure decides the job. They fix into the scaffold with standard clamps, and they are used for beam bridges, gantries, walkways and bridge maintenance platforms.

Scaffold ladders, ladder gates and temporary stairs
Access to the working lifts is by ladder or by stair, and the choice follows the traffic and the length of the job: a ladder bay serves erectors and small gangs on shorter programmes, while a temporary stairway suits sites where many operatives, or operatives carrying tools and materials, move between levels every day for months. The full access range is under scaffold ladders and stairways.
Steel scaffold ladders
Steel scaffold ladders are galvanised, with angled non-slip rungs, and are made for the ladder bay of a scaffold. Lengths run from 3m to 6m, so a ladder can be chosen to reach from one lift to the next and still rise above the landing as a handhold.
Scaffold ladder gates
Where the ladder comes up through the guardrail, a scaffold ladder gate closes the gap. Its spring hinge swings the gate shut behind each person who passes, its toe board stops tools and materials sliding off at the opening, and welded couplers clamp it to the existing tube.
Modular steel stairways
The modular steel stairway is built from step units that connect to give the rise the job needs, up to 7.7m, and it fixes to a scaffold or a concrete slab. It is the stair for between-floor access in phased construction and for embankment slopes in groundworks and civils, where the stair stays in place for the whole phase.
Temporary aluminium stairways
The temporary aluminium stairway is light enough to move and reset by hand and has an adjustable pitch, so it suits jobs where the stair changes position as the work moves, such as temporary site entrances and mezzanine access. Paired with trench bridges, it gives stepped access over an open excavation.
Scaffold base jacks, base plates and fittings
The ground decides what goes under each standard, and the type of scaffold decides which fittings go into the structure above it.
Base plates
Scaffold base plates are flat steel plates that sit under each standard on firm, level ground such as concrete or tarmac. They spread the load of the tube over a wider area and protect the surface beneath. On soft ground, general practice is to lay a timber sole board under the base plate or base jack to spread the load further.
Adjustable base jacks
Adjustable base jacks combine a threaded stem with a base plate, and they level system scaffold on uneven or sloping ground by setting each standard to the right height. The rating is chosen by the load the scaffold design puts on each standard: the 4 tonne base jack for general loading and the 6 tonne base jack for heavier loading.
Couplers and sleeve couplers
Scaffold couplers clamp tubes together in the structure, and sleeve couplers join two tubes end to end to extend a run. In formwork and temporary works, prop bracing double couplers fix tube to a steel prop at a right angle and prop swivel couplers fix it at any angle, so a line of props can be braced with scaffold tube.
ReadyFix transoms
The ReadyFix transom is a prefabricated structural transom for tube and fitting scaffold. It holds the boards in place without the separate clips and fittings a tube transom needs, which shortens both erection and dismantling, and it comes in three, four and five board widths.
Tube ties for handrails
Scaffold tube ties fix a handrail to an upright scaffold pole, in single and double versions for one rail or two. Tube, boards and the full fittings range are under scaffold boards, tube and fittings.

Brick guards, catch fans and guardrail feet
What lies below and beside the scaffold decides the debris protection: guards at the working lift keep materials on the platform, and a catch fan stops what still falls past the face where people pass underneath. Full enclosure of the face is done with scaffold sheeting, and guardrails for slabs, roofs and open edges are under edge protection systems.
Scaffold brick guards
Scaffold brick guards hook onto the guardrails at each working lift and clip to the toe board, closing the gap between the two where bricks, blocks and tools are stacked on the boards. They are made from recycled plastic and stack flat for transport between jobs.
Catch fans
A catch fan projects out from the scaffold to catch anything that falls past the face, over pavements, entrances and other public areas. The mini catch fan clips straight onto the guardrail and suits smaller scaffolds and maintenance work. The safety net catch fan is for high-rise and tight inner-city sites: it mounts to scaffold, slab or wall edges without a crane, its fine mesh holds small tools and debris, and it folds up to clear crane paths and lifting zones.
SG4 handrail feet
SG4 handrail feet are the galvanised bases for the Shorguard SG4 guardrail system. They hold the guardrail steady and leave the area beneath the barrier clear to move through.
Scaffold lights
HERMEQ supplies scaffold lights in three mounting formats, and the choice follows where the light has to sit. The vertical mount safety light fits on top of a tube end or bolts to a flat surface such as timber hoarding or fencing, and it marks the corners of scaffold towers, stairwells and riser structures. The side mount site light clamps along a tube and lights scaffold perimeters, temporary walkways and working edges beside traffic or pedestrians. The scaffold light fits any scaffold pole with a half swivel fitting and has a tamper-resistant steel casing for scaffolds that face a road or a public footway. The vertical and side mount lights switch between two modes: flashing to warn of a hazard or an edge next to traffic, and steady to mark an outline or a route that people follow after dark.

Trestle tables and trestle edge protection
Trestles give a low-level working platform for plastering, painting, fit-out and facade work where a full scaffold is more than the job needs, and the trestle components turn that platform into a guarded one.
Builders trestles
Builders trestles are zinc-plated steel stands, adjustable in height with locking pins, that carry scaffold boards to form the platform. They fold for transport and storage between jobs.
Safety posts and S brackets
Trestle safety posts fit to flat-top trestles and are slotted to take scaffold boards as guardrails and toe boards. Trestle board S brackets join and overlap boards, handrails and toe boards, so the platform and its edge protection run continuously along the length of the work.
Stabilisers
Trestle stabilisers are fitted one per trestle when the platform is used above 1.2 m. They brace each trestle against sideways movement and reduce deflection as operatives and materials move along the boards.
Gates and ladder brackets
Where the ladder meets the face of the platform, the trestle ladder bracket fixes the ladder to the trestle system and the trestle gate closes the access point with a locking steel gate. The ladder bracket and the S bracket are made to BS EN 13374, the standard for temporary edge protection systems. For work above trestle height, scaffold towers give a taller platform.
Popular Categories

Boards, Tube & Fittings
View Products >

Ladders & Stairways
View Products >

Scaffolding Storage
View Products >
Frequently Asked Questions
What counts as a scaffolding accessory?
A scaffolding accessory is a component used with tube, boards and fittings to make a scaffold accessible, level, safe to work on or safe to pass beneath. Tube, boards and the full fittings range, sheeting, towers and storage each have their own category.
Which standards do scaffolding accessories carry?
The steel scaffold ladders are certified to BS EN131 Parts 1, 2 and 3 under the BSI Kitemark. The base jacks are tested to BS1139 and EN74, and the prop bracing couplers to EN74-1 Class B. Builders trestles are certified to BS 1139-4, the ReadyFix transom complies with TG20:13, the scaffold brick guards are certified to SG10:19, and the aluminium beams are designed to BS EN 1999-1-1.
Do scaffold accessories work with system scaffold as well as tube and fitting?
Most accessories in the range clamp to standard scaffold tube, so they fit tube and fitting scaffold and the tube elements of a system scaffold. Ladder beams and aluminium beams fix in with standard couplers and clamps.
Do scaffold lights switch on by themselves?
Yes. The half swivel scaffold light has a daylight sensor and only comes on in low light, and the vertical mount and side mount lights have a built-in photocell that switches them with the light level. All three run on batteries, so they need no cable to the scaffold.
Can aluminium scaffold beams be joined to make a longer span?
Yes. Aluminium scaffold beams join end to end with spigots held by spring clips, which are available as connectors for the beams. The length of a joined beam line and the points where it is supported are set by the scaffold design.
What is the difference between a base jack and a U-head?
A base jack sits at the foot of a standard on its own base plate, and its threaded stem sets the scaffold level on uneven ground. A U-head sits at the top of a steel prop or a system scaffold standard, and its U-shaped cradle holds a timber or steel beam in formwork and propping.










































































































































