Spill Absorbents
HERMEQ spill absorbents soak up and contain leaks and spillages before they spread across a floor, reach a drain or contaminate the ground. The range is graded for general purpose, oil and fuel, and chemical spills, so the absorbent can be matched to the liquid for a quick response to any leak or spillage incident. Formats cover absorbent pads, rolls, socks and cushions, land, drain and marine booms, and polymer oil absorption pillows and oil retention booms. They are used alongside our drip trays and drum containment to catch leaks where they start, with nationwide delivery on every order.
-
Land Boom – General Purpose – With Netting, Rope, Clips & Rings – 12cm x 3m£56.36 £67.632 to 3 Week Delivery
Types of spill absorbents
The range divides by job: pads, rolls, socks and cushions soak liquid up, booms surround a spill to stop it spreading, and the polymer pillows and retention booms turn oil and fuel into a solid that cannot drain back out.
Absorbent pads and spill mats
Pads, also sold as spill mats or oil mats, are the first response to drips, leaks and small spills on floors, benches and hardstanding. They are laid flat over the liquid, wick it in and lift away in one piece. Pads are made in all three grades, and general purpose absorbent pads are the usual stock for a workshop, production area or maintenance bay.
Absorbent rolls
Roll is cut to length, so it is the format to choose when the area to protect is larger than a few pads can cover. A general purpose absorbent roll lines walkways and lies under static plant during maintenance, and the chemical grade catches overspray around process equipment.
Absorbent socks
Socks, also known as snakes or absorbent tubes, are flexible filled lengths that bend round the base of a leaking machine, the edge of a spill or a doorway. They absorb on contact and are left in place to keep walkways clear of the oil, coolant and hydraulic fluid that leaks from plant and machine tools. Absorbent socks are made in general and oil and fuel grades.
Absorbent cushions
Cushions, often called absorbent pillows, are filled bags that sit directly under leaking hoses and fittings, on a spill or inside a drip tray. In a tray they take up the collected fluid, so the tray can be emptied without a second spill. The range holds general purpose absorbent cushions with matching oil and fuel and chemical versions.
Land booms
Land booms are larger in diameter than socks and are laid round a spreading spill on hardstanding to hold it in one place while it is absorbed; some suppliers sell them as spill barriers. Land booms come in general purpose, oil and fuel and chemical grades. Where one boom will not reach, the connectable land boom set joins several booms into one continuous barrier.
Mini drain booms
These compact booms go into drains, sumps and tanks where access is too tight for a full size boom. They are water repellent and can be left in place to take up oil, diesel and other hydrocarbons without absorbing the water. Mini drain booms suit drainage that carries surface water from a yard, fuel point or plant compound.
Marine booms
Marine booms float and take up only diesel and other hydrocarbons, so they are the boom for ponds, lakes, rivers, marinas and harbours. Laid across or around a sheen, marine oil booms hold it on the surface while it is absorbed.
Oil absorption pillows
Oil absorption pillows contain a polymer that turns oil and fuel into a solid, rubber-like mass, so the absorbed hydrocarbon does not leak or drain out again. They are made for contained standing water, such as a flooded excavation, a sump or a bunded area, where oil sits on the surface and has to be lifted off the water.
Oil retention booms
Oil retention booms use the same polymer in boom form to make a barrier that absorbs and solidifies hydrocarbons on water or land. They come in marine and quick deployment types across a choice of lengths.

General purpose, oil and fuel or chemical absorbents
The grade is decided by the liquid and by whether water is present. General purpose absorbents take up non-hazardous liquids such as water, coolant, light oils, solvents and everyday workshop fluids, and they absorb water as readily as oil. Outdoors, in rain or over standing water, a general purpose pad fills with water along with the oil and is used up far sooner.
The oil and fuel grade is water repellent and takes up only oils, fuels, oil-based solvents and other hydrocarbons, so it is the grade for yards, plant compounds, wet ground and work on or near water. Oil and fuel absorbent pads are the pad to carry for outdoor work. Under plant stored outside, where rainwater collects in the drip tray with the leaked oil, oil and fuel absorbent cushions are the right fill for the tray.
The chemical grade is for acids, alkalis and strong chemicals, and it is also the grade to use when the spilled liquid cannot be identified. It is made as chemical absorbent pads and land booms for spills on the floor. A chemical absorbent roll lines the floor under process equipment, filling points and chemical stores, and chemical absorbent cushions go under leaking drums and in their drip trays.
Absorbent pad and roll grades, weights and packs
Each pad and roll is listed by quality grade, sheet weight and pack, and each choice follows from how often the stock is used and where it is kept.
Premium or value grade
Premium grade suits workshops and sites that use absorbents every day or deal with larger and more frequent spills, where each sheet has to do more work before it is changed. Value grade suits routine drips, wiping down and stock held for occasional spills, where a larger quantity on hand matters most.
Single or double weight
Single weight is the lighter sheet, used for drips, wiping tools and parts, and catching small leaks under a machine. Double weight is the thicker sheet for pooled liquid and larger spills, where fewer sheets are needed to lift the same spill.
Dispenser box, clip top bag, poly wrapped or boxed
A dispenser box sits on a bench or shelf at a fixed station, such as a maintenance bay or fuel point, where pads are taken one at a time as they are needed. A clip top bag is the pack for a van, a site cabin or the cab of a machine, because it closes again after use and keeps the remaining pads dry and clean. Poly wrapped and boxed packs are bulk stock for a stores or compound, held for restocking the stations and vehicles.

Containing and cleaning up a spill
A spill response runs in a fixed order: stop the source, protect the drains, contain the liquid, absorb it and bag the waste. Drains near the spill are protected next with a mini drain boom or one of our drain covers, because liquid that reaches drainage is far harder to recover than liquid on hardstanding.
The spill is then surrounded with socks or land booms to stop it spreading, and absorbed with pads or cushions laid from the outside edge inwards so the wetted area gets smaller as the work goes on. Used absorbent is bagged and labelled with the liquid it holds. The absorbents for each step can be bought individually or ready packed in spill kits for a fuel point, plant compound or workshop.
Popular Categories

Wheelie Bins
View Products >

Waste Skips
View Products >

Tipper Skips
View Products >
Frequently Asked Questions
How do you dispose of used spill absorbents?
Used absorbent takes on the hazard of the liquid it holds, so it is classified and disposed of on that basis. Absorbent holding oil, fuel or chemicals is normally hazardous waste and goes to a licensed waste carrier with the correct consignment paperwork.
Why use absorbent pads instead of loose granules?
Pads, rolls and cushions lift away in one piece, while loose granules have to be spread, worked in and swept up, and granules left behind are a common cause of cross contamination. Formed absorbents are quicker to put down and pick up.
How much spill absorbent should a site keep?
Hold enough absorbent to deal with a full spill from the largest single container, tank or bowser on site, kept close to where that container is used. Day to day stock for drips and maintenance sits on top of that reserve.
What is the difference between spill absorbents and a spill kit?
Spill absorbents are the individual pads, rolls, socks, cushions and booms, bought loose to restock or to cover a particular job. A spill kit packs a selection of these formats into one container, so a complete response sits ready at a fuel point, on plant or in a vehicle.
How should spill absorbents be stored?
Keep absorbents dry, in their packs and close to where spills are most likely, such as fuel points, plant compounds, workshops and chemical stores. A general purpose absorbent that has already taken on water has less capacity left for the spill it is needed for.










































































































































