Road Forms
Road forms are the steel edge shuttering that holds concrete to line and level on slabs, roads, kerbs and foundations, and HERMEQ supplies them for groundworks, civils and construction work. The range includes rigid road forms for straight, square shuttering and flexible road forms for curves and non-standard layouts. Custom broad base forms and the K-Form leave-in-place screed rail cover the jobs the standard forms do not. The steel forms are pressed from sheet and locked to driven stakes, so the same set is struck, cleaned and reused from pour to pour. They come in a choice of depths to suit the slab thickness and are held in permanent UK stock.
Rigid and flexible road forms
Most sets of road forms, which the trade also calls road formers or roadforms, are built from rigid forms with flexible lengths added for curves, and the custom and leave-in-place types cover the work those two do not.
Rigid road forms
Rigid road forms are pressed steel shuttering for straight edges on ground slabs, roads, foundations and hardstandings. Laid end to end and locked to stakes driven through the back, they hold a true line while concrete is placed, compacted and struck off against the top edge. They are the core of any set and the type to buy first, with the other types added only where the layout calls for them.
Flexible road forms
Flexible road forms bend to a radius, so they shutter curved edges on drives, footpaths, kerb lines and public paving. On a mixed run, rigid forms take the straights and flexible 3m lengths take the curves, and both are held by the same stakes, so one set of fixings serves the whole edge. Choose them wherever the drawing shows a bend that a line of straight forms could only follow in facets.
Custom broad base road forms
Custom broad base road forms are built to order for slab, kerb and roadwork edges that the standard range does not suit. Height, rigidity, bracing and edge finish are set to the job, and the forms take the same stakes and stillages as the standard range. They are the choice for repeat work to a non-standard profile, where a set made to the detail replaces packing and adapting standard forms on every pour.
K-Form leave-in-place screed rail
The K-Form K135 screed rail is a UPVC rail that stays in the concrete once the slab is poured. Steel road forms are struck, cleaned and reused, while K-Form is left in place, so adjoining bays can be poured one after another without waiting to strike the edge between them. Holes in its face locate dowel bars across the joint, and a top strip lifts out once the concrete has set to leave a slot for joint sealant. Choose it for multi-bay internal slabs where the joints are planned and the floor is poured in a continuous sequence.

Road form depths, holes and edges
Once the type is settled, a rigid form is chosen by the slab it has to hold: how thick it is, whether it ties into the next bay and how its edge will be finished.
Matching form depth to slab thickness
Steel road forms come in depths from 100mm to 300mm across the range, and the form depth is matched to the finished slab thickness, so each slab takes a form of the same depth. The top edge of the form becomes the screed line, which means the form is set to finished level and not to the formation. Where the formation dips below the bottom of the form, the gap is closed before the pour so concrete cannot run out beneath the edge.
Drilled road forms or no holes
Drilled forms have holes along the face for dowels or reinforcing bar to pass through and tie one bay to the next. They are the choice for roads, hardstandings and slabs poured in bays, where the bars carry load across the joint. Rigid road forms with no holes leave an unbroken face, and they suit a single slab or an edge that will stay exposed, where a clean edge matters more than a tie. A contractor who pours both kinds of job often keeps a set of each.
Square or rounded edge
The top edge of the form shapes the arris of the slab. The drilled rigid forms are square edged, which gives a sharp arris where the slab will butt tightly against another bay, a kerb or a building. The no-hole forms have a rounded top edge, which leaves a softened arris on edges that stay exposed to foot traffic or wheels. Custom broad base forms are made with either edge to order.
Road forms for slabs, roads and kerbs
The same forms do different jobs depending on what they shutter, and each use puts the emphasis on a different part of the setting out.
Ground slabs and hardstandings
On large slabs the bay layout comes first. Setting bay widths to whole form lengths keeps runs closed without short makeweights, and planning the pour sequence decides where joints fall and which edges need dowels. Where concrete is placed by crane, concrete pouring skips let the gang discharge close to the form without loading one section of the run heavily.
Roads, footways and kerb lines
Long runs depend on holding line and level from the first form to the last. Every lock housing should carry a stake, joints between forms should sit flush, and crossfall is set by the top edge of the forms, so it is checked along the run before concrete arrives. Rechecking the line after the first loads are placed catches any movement while it can still be corrected.
Driveways and paths
Domestic and landscape work brings curves and falls together. The radius is best set out first with pegs and a line, and the form is then bent to it, so the curve runs smoothly. Falls away from buildings and towards drainage points are built into the form level, because the screed follows the top edge exactly.

Road form stakes, pins and storage
The accessories below are sized to the same 3m forms and stakes, so they work across the rigid, flexible and custom types without separate fixings for each.
Road form stakes
Road form stakes, which many in the trade call road form pins, are mild steel bars with a sharp point. Each one passes through a lock housing on the back of the form, is driven into the subgrade and is then locked with the wedge in the housing, which holds the form tight against the stake while the concrete is placed.
Road form stake extractor
The road form stake extractor is a lever tool that pulls stakes out of the ground once the concrete has set. Levering against the ground in place of striking the stake sideways keeps the stakes straight and avoids bending the forms, and it lifts stakes from compacted or stony ground that would otherwise hold them fast.
Road form stillages
Road form stillages are steel box section racks built to take 3m forms for storage and transport. They have forklift guides, removable arms and stackable legs, so loaded stillages stack in the yard and empty ones collapse. They come in self-colour or painted finishes, which lets a contractor or plant yard mark its own stock.
Combiform screed rails and levelling parts
The Combiform screed rail is a steel rail system for setting internal floor levels and forming joints in one operation. Locking clips stiffen the rail, steel ground plates carry it, and adjusting screws turned with the adjusting tool set it to height for flat or sloping slabs. A screed rail top extender adds depth for a thicker topping and forms a contraction joint in place of a saw cut.
Popular Categories

Road Plates
View Products >

Bog Mats
View Products >

Reinforcing Bar & Steel Plate
View Products >
Frequently Asked Questions
How many stakes does each road form need?
Each 3m road form takes three stakes, one through each lock housing on the back, which puts them at about 1m centres along the run. Each stake is driven into the subgrade and locked with its wedge. Custom broad base forms use the same three stakes per form.
Are road form pins the same as road form stakes?
Yes, road form pins and road form stakes are two names for the same item. HERMEQ lists them as road form stakes, and the same stake fits the lock housings on the rigid, flexible and custom broad base forms, so one stock of stakes serves the whole set.
Should road forms be oiled before a pour?
Coating the face of the form with a release agent or mould oil before each pour stops the concrete bonding to the steel. A thin, even coat is enough, and wiping off any surplus avoids marking the slab edge. Oiled forms strike more cleanly and take less cleaning afterwards.
Are steel road forms reusable?
Steel road forms are made to be struck and reused on job after job. Once the concrete has gained enough strength, the stakes are drawn, the forms are lifted away and residue is cleaned off while it is still soft. Stored flat in stillages, forms stay straight and ready for the next pour.
How are road forms set to line and level?
A string line is set out at the finished slab level, and the forms are placed to it and joined end to end. Stakes are driven through the housings, the top edge is checked with a level or laser along the run, and the forms are adjusted until line and level are right. Only then are the wedges driven home to lock each form to its stakes.
Where are HERMEQ road forms made?
HERMEQ manufactures in the UK, with in-house steel processing. The rigid and flexible road forms, stakes and stillages are made in Great Britain and held in permanent UK stock.










































































































































