Wildlife Protection
Wildlife fencing, also called newt fencing, amphibian fencing or drift fencing, is used on construction and infrastructure sites to keep protected species out of harm during clearance, groundworks and access works. The fences guide and restrict the movement of amphibians, reptiles and water voles, so that a site can meet its environmental responsibilities and comply with ecological regulations.
HERMEQ supplies exclusion fencing for newts, slow worms, reptiles, grass snakes and water voles in rolls and panels, permanent guidance systems for roads, and the pitfall traps and refuge tiles used in trapping and translocation. The range is available to buy online with nationwide delivery.
Newt, reptile and water vole fencing
The range is organised by the species a fence has to stop, and height rises with the size of the animal and its ability to climb, from 750mm panels for newts and slow worms up to 1.7m panels for water voles.
Newt and slow worm fencing
Newt and slow worm fencing is a panel fence for keeping great crested newts, smooth newts and slow worms out of a works area. It suits sites where the ecological survey has recorded amphibians and slow worms in the same habitat, because one fence line excludes both.
One-way newt fencing
One-way newt fencing holds newts on their habitat side of the line while smaller creatures continue to pass through it. It is the fence for a boundary between retained habitat and the works, where the aim is to keep a newt population in place and leave other small wildlife free to move. Where every animal has to be kept out of an area, a solid exclusion fence is the right product.
Semi-permanent newt fence on a roll
The semi-permanent newt fence comes as a continuous roll for newts, other amphibians and reptiles. On long runs such as pipeline, cable and road corridors, a roll leaves far fewer joins in the fence line, and joins are the points where a newt fence is most likely to be breached.
Permanent newt panels
Permanent newt panels are rigid sheets for amphibian and reptile exclusion where the fence has to stay sound through a long programme or remain after it.
Reptile fencing
Reptile fencing restricts the movement of reptiles while letting smaller creatures through, so invertebrates and other small animals keep crossing the line. It is the fence to specify where the survey has found lizards or slow worms on land due for clearance and only the reptiles need to be kept out of the works.
Snake fencing
Grass snakes climb and reach higher than newts or lizards, so they need a taller barrier than a standard amphibian fence. Snake fencing panels keep grass snakes and other reptiles out of construction areas, and the HDPE and woven snake fence gives a choice of rigid or woven material at two heights.
Water vole fencing
Water voles burrow into banks, so works on riverbanks, ditches and wetland margins need the tallest fences in the range. Water vole fencing keeps water voles out of works areas near water, and water vole fence panels, designed in consultation with ecologists, have an anti-climb profile that also stops other small mammals and rodents.
Permanent wildlife barriers, road tunnels and stop grids
The permanent wildlife barrier is for exclusion and mitigation fences that become a lasting part of a development and guide amphibians and reptiles along a set route. Where a road crosses a migration route, amphibian road tunnels and stop grids complete the system: guidance fences lead animals to a tunnel under the carriageway, and stop grids keep them off the road where an access breaks the fence line.

Temporary, semi-permanent and permanent newt fencing
Two things decide the format: how long the fence has to stay up, and how much disturbance it will take from people, plant and traffic. The semi-permanent roll is made for sites with a medium risk of human disturbance and has a life expectancy of up to 5 years, which covers a phased development or a survey and trapping period that runs over several seasons.
Rigid HDPE newt panels give up to 15 years of service and are the choice for perimeters beside haul roads and plant routes, sites open to the public, and receptor areas that have to hold a population long after the works finish. When a programme is likely to be extended, specifying the longer life format at the start avoids replacing the fence partway through the works.
Amphibian fencing for site works and surveys
Excluding wildlife from works areas
An exclusion fence goes in before vegetation clearance and topsoil strip, so animals are kept off the ground before machines reach it. What matters is a closed line: the fence follows the works boundary without gaps, turns back at its ends or meets another barrier, and is checked after heavy rain, frost and any plant movement close to it. Silt fencing to hold run-off from the same works is in the erosion and sediment control range, and bank protection for works alongside ditches and rivers is in water margin protection.
Trapping and translocation enclosures
For a translocation, the fence encloses the area to be cleared and animals are caught inside it under the ecologist's supervision before works start. Pitfall traps are set flush with the ground against the inside of the fence, where animals following the barrier drop into them, and refuge tiles are laid in sunny spots inside the enclosure, where amphibians and reptiles shelter under them and are found on each check. The fence line, traps and refugia work as one system, so they are best ordered together against the ecologist's method statement, which sets the trap spacing and the number of tiles for the enclosure.

Installing newt and reptile fencing
A newt or reptile fence works only if animals cannot get under it, over it or through its joins. The lower edge is buried in a trench with a return turned toward the side the animals are on, so a burrowing newt meets the buried return, and the top edge has a return or lip angled toward the same side, so a climbing animal meets an overhang. Stakes or posts go on the side the animals are kept out of, so they cannot be used as a ladder.
Joins are overlapped and fixed through both layers at a post. The backfill is compacted firmly against both faces of the fence so that no voids remain, since a void gives animals a way under the fence or a place to hide during trapping.
Popular Categories

Geotextiles
View Products >

Grass & Gravel Paviours
View Products >

Geogrids & Geocells
View Products >
Frequently Asked Questions
When is newt fencing required?
Newt fencing is required when great crested newts or their habitat are present on or near a development site and the works could harm them. The species is protected under the Wildlife & Countryside Act 1981, the Conservation Regulations 1994 and the EC Habitats and Species Directive, which make it an offence to kill, injure or disturb the animals or to damage their habitat. Reptiles and water voles are also protected under the Wildlife & Countryside Act 1981, and their fencing follows the same principle.
Who decides which wildlife fencing a site needs?
The project ecologist specifies the fence from the species recorded in the survey, and the method statement or protected species licence sets the fence line, the fence type and the trapping effort. The contractor then supplies and installs the fence to that specification.
What height of fence do snakes and water voles need?
Snake fencing in the range comes in two heights, 1.2m in rigid HDPE and 1.38m in woven material, and both stand well above a standard newt fence. Water voles need the water vole fences and panels, which stand higher again.
How is wildlife fencing sold, and how much do I need?
The range is sold as rolls and as individual panels, priced per roll or per panel, and dividing the price by the length supplied gives a cost per metre. To work out a quantity, measure the full length of the fence line including the returns at its ends, then allow for the overlap at each join. Dividing the run by the effective length of one panel or roll gives the number to order, with a small allowance for corners and cutting.
What is the fencing made from?
Most of the range is recycled plastic. The newt and slow worm, one-way newt and water vole fences are recycled polypropylene, the reptile fencing is polypropylene, the permanent newt panels are UV-stabilised recycled HDPE, and the semi-permanent newt fence is UV-stabilised recycled plastic that is non-toxic and chew-resistant. These panel fences and the permanent newt panels are manufactured in the UK, and the semi-permanent newt fence contributes to a BREEAM score.











































































































































